Oval Cast Brass CS
The one piece Oval Belt Plate is solid Cast Brass with cast brass hooks on the back. It has three brass prong hooks for attaching to the belt.
NAA 706
Enquiry about Oval Cast Brass CS
Captcha
Related Products
-
Oval Cast Brass OVI Ohio Volunteer Infantry
Ohio Volunteer Infantry (OVI) Belt Plate
The one piece Oval Belt Plate is solid Cast Brass with cast brass hooks on the back. It has three brass prong hooks for attaching to the belt.
NAA 709
-
Box Plate NC
The oval cartridge box plate is lead filled stamped sheet brass. It has 2 brass loops on the back for attaching to the cartridge box.
NAA 736
-
Oval Lead Filled SC
The one piece Oval Belt Plate is lead filled stamped sheet brass with the brass hooks on the back embedded in the lead. It has three prong hooks for attaching to the belt.
NAA 718
-
Belt Plate Oval Lead Filled Georgia
The one piece Oval Belt Plate is lead filled stamped sheet brass with the brass hooks on the back embedded in the lead. It has three prong hooks for attaching to the belt.
NAA 712
-
Belt Plate Oval Cast Brass Mississippi
The one piece Oval Belt Plate is solid Cast Brass with cast brass hooks on the back. It has three brass prong hooks for attaching to the belt.
NAA 714
-
Belt Plate Oval Cast Brass Alabama
The one piece Oval Belt Plate is solid Cast Brass with cast brass hooks on the back. It has three brass prong hooks for attaching to the belt.
NAA 708
-
2-Piece Solid Brass CSA
This 2-Piece Belt Plate is solid cast brass. It is copied from the original with particular attention to detail.
This belt plate is for use with the 1 5/8 inch NCO / Officer belt or the 1 5/8 inch Saber / Sword Belt.
NAA 726
-
Buckle Spoon & Wreath Florida
This two piece Florida “spoon & wreath” buckle is solid cast brass. It is copied from the original with particular attention to detail.
This buckle is for use with the 1 5/8 inch NCO / Officer belt or the 1 5/8 inch Saber / Sword Belt.
NAA 700
-
Baldric Plate Federal Eagle
Stamped sheet brass, lead filled. Three prongs are embedded into the lead to facilitate fastening the plate on to your NCO Baldric strap. This plate is supposed to be right in the center of your chest when mounted on the strap per US regulations.
NAA 737
-
Saber or Sword Belt Hanger Snap Swivel
Brass. Used for Saber and Sword Belt Hangers. Copy of Original.
Sold individually.
NAA 702
-
Buckle 2-Piece Solid Brass M1874 US
This two piece buckle is solid cast brass. It is copied from the original, circa 1874, with particular attention to detail.
This buckle is for use with the 1.75″ NCO / Officer belt or the 1.75″ Saber / Sword Belt. If purchased with the belt we will install the buckle at no additional charge.
NAA 732
-
Buckle Forket Tongue
The one piece buckle is solid cast brass. It is copied from the original, circa 1861-1865, with particular attention to detail. This style was worn by Confederate soldiers. The ‘tongue’ style frame buckle refers to the class of Confederate frame buckles made with some form of movable tongue.
This buckle will fit a 1 3/4″ wide belt.
NAA 730
-
Box Plate CS
The oval cartridge box plate is lead filled stamped sheet brass. It has 2 brass loops on the back for attaching to the cartridge box.
NAA 734
-
Belt Plate Oval Cast Brass New Jersey
This 1863 New Jersey Oval Cast Brass Belt Plate. It has 3 Brass hooks for attaching to the belt. The 1863 belt plate measures approximately 1 5/8 inches x 2 3/4 inches.
NAA 711
-
Belt Plate 1-Piece Solid Brass NC
This 1-piece Belt Plate is solid cast brass. It is copied from the original with particular attention to detail. It has three brass prongs for attaching to the belt.
NAA 716
-
Box Plate US
The US Cartridge Box Plate measures approximately 3.5 inches wide x 2 1/4 inches high. The box plate is lead filled stamped sheet brass. It has 2 brass loops on the back for attaching to the cartridge box.
NAA 733
-
Belt Keeper
The brass Belt Keeper was commonly utilized on mid to late war M1855 Enlisted waist belts for Federals. They began to appear by early 1863 to replace the leather loop keeper that had been the standard prior to the war. The keeper has prongs to fasten to the leather waist belt.
NAA 701
-
Saber or Sword Belt Brass Stud
Solid brass, double headed stud used on saber/sword belts and knapsacks. Each saber/sword belt used four studs to attach the top and bottom sword hangers. These are replacement studs as our saber belts come complete.
NAA 703
-
Oval Lead Filled SNY
State of New York
The one piece Oval Belt Plate is lead filled stamped sheet brass with the brass hooks on the back embedded in the lead. It has three prong hooks for attaching to the belt.
NAA 719
-
Breast Plate Federal Eagle
Stamped sheet brass, lead filled. Two loops are embedded into the lead to facilitate fastening the plate on to your cartridge box strap. This plate is supposed to be right in the center of your chest when mounted on the sling per US regulations.
NAA 735
-
2-Piece Solid Brass M1851 Value Line Federal Eagle with Silver Wreath
This 2-Piece Belt Plate Value Line is solid cast brass with a one-piece applied nickels silver wreath. It is a very nice copied from the original with particular attention to detail. This belt plate was worn by both Confederate and Union Officers during the Civil War.
NAA 725
-
Buckle Georgia Frame
The one piece buckle is solid cast brass. It is copied from the original, circa 1861-1865, with particular attention to detail. This style was worn by Confederate soldiers. The ‘standard’ style frame buckle refers to the class of Confederate frame buckles made with integral raised hooks and a flat back.
This buckle will fit a 2″ wide belt.
NAA 731
-
Oval Lead Filled US M1839
This M1839 Oval Lead Filled Belt Plate was used by infantry soldiers through about 1861. The one piece oval belt plate is lead filled stamped sheet brass with the brass hooks on the back embedded in the lead. It has two prong hooks for attaching to the belt. The M1839 belt plate measures approximately 1 5/8 inches x 2 3/4 inches.
NAA 710
-
2-Piece Solid Brass Federal Eagle
This 2-Piece Belt Plate is solid cast brass. It is copied from the original with particular attention to detail. This belt plate is for use with the 1.75 inch NCO / Officer belt or the 1.75 inch Saber / Sword Belt.
NAA 723
-
Oval Lead Filled Texas
The one piece Oval Belt Plate is lead filled stamped sheet brass with the brass hooks on the back embedded in the lead. It has three prong hooks for attaching to the belt.
NAA 721
-
Spoon & Wreath Texas
This two piece “spoon & wreath” buckle is solid cast brass. It is copied from the original, circa 1861-1865, with particular attention to detail.
This buckle is for use with the 1 5/8 inch NCO / Officer belt or the 1 5/8 inch Saber / Sword Belt. If purchased with the belt we will install the buckle at no additional charge.
NAA 728
-
Oval Lead Filled OVM
The one piece Oval Belt Plate is lead filled stamped sheet brass with the brass hooks on the back embedded in the lead. It has three prong hooks for attaching to the belt.
NAA 717
-
1-Piece Solid Brass CSA
This 1-piece Belt Plate is solid cast brass and is appropriate for the Confederate enlisted soldier. It is copied from the original, circa 1861-1865, with particular attention to detail. It has three brass prongs for attaching to the belt.
NAA 722
